? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded power inductors C lps3008 document 438-1 document 438-1 revised 08/25/10 dcr srf i sat (a) 5 i rms (a) 6 inductance 2 max 3 typ 4 10% 20% 30% 20c 40c part number 1 20% (h) (ohms) (mhz) drop drop drop rise rise lps3008-561ml_ 0.56 0.072 330 1.8 2.0 2.1 1.4 2.0 lps3008-801ml_ 0.80 0.092 255 1.6 1.7 1.8 1.1 1.6 lps3008-102ml_ 1.0 0.125 220 1.3 1.4 1.5 0.90 1.3 lps3008-152ml_ 1.5 0.134 170 1.1 1.3 1.3 0.87 1.2 lps3008-222ml_ 2.2 0.175 150 1.0 1.1 1.1 0.85 1.1 lps3008-332ml_ 3.3 0.285 114 0.81 0.86 0.88 0.74 0.95 lps3008-472ml_ 4.7 0.350 87 0.68 0.73 0.74 0.68 0.80 lps3008-562ml_ 5.6 0.450 78 0.62 0.67 0.70 0.58 0.73 lps3008-682ml_ 6.8 0.500 75 0.58 0.61 0.63 0.50 0.67 lps3008-822ml_ 8.2 0.600 61 0.52 0.56 0.58 0.45 0.60 lps3008-103ml_ 10 0.650 56 0.46 0.51 0.52 0.42 0.56 lps3008-123ml_ 12 0.790 49 0.45 0.48 0.50 0.38 0.50 lps3008-183ml_ 18 1.25 38 0.35 0.38 0.40 0.33 0.44 lps3008-223ml_ 22 1.50 35 0.29 0.33 0.34 0.29 0.38 lps3008-333ml_ 33 2.30 23 0.27 0.30 0.31 0.25 0.32 lps3008-473ml_ 47 3.00 21 0.22 0.23 0.24 0.21 0.27 lps3008-683ml_ 68 4.75 18 0.18 0.19 0.20 0.175 0.23 lps3008-104ml_ 100 6.85 14 0.15 0.16 0.16 0.160 0.21 lps3008-124ml_ 120 7.00 13 0.084 0.094 0.10 0.140 0.190 lps3008-154ml_ 150 8.00 11 0.080 0.088 0.092 0.130 0.175 lps3008-184ml_ 180 9.00 10 0.070 0.078 0.082 0.120 0.160 lps3008-224ml_ 220 11.5 9 0.067 0.073 0.076 0.100 0.145 lps3008-334ml_ 330 18.0 7 0.059 0.064 0.066 0.090 0.130 1. please specify termination and packaging codes: lps3008-104m lc termination: l = rohs compliant silver-palladium- platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (1000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d =13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (3500 parts per full reel). 2. inductance tested at 100 khz, 0.1 vrms using an agilent/hp 4192a. inductance at 1 mhz is the same for parts with srf 10 mhz. 3. dcr measured on a micro-ohmmeter. 4. srf measured using an agilent/hp 8753es or equivalent. 5. dc current that causes the specified inductance drop from its value without current. 6. current that causes the specified temperature rise from 25c ambient. 7. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering. core material ferrite core and winding loss see www.coilcraft.com/coreloss terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. weight 22 ? 25 mg ambient temperature ?40c to +85c with i rms current, +85c to +125c with derated current storage temperature component: ?40c to +125c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 1000/7 reel; 3500/13 reel; plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth recommended pick and place nozzle od: 3 mm; id: 1.5 mm pcb washing only pure water or alcohol recommended ? very low dcr; excellent current handling ? only 0.8 mm tall; 3.0 3.0 mm footprint coilcraft designer?s kit c392 contains samples of 0.80 h to 33 h parts (3 each) from lps3008, lps3010 and lps3015. kit c401 contains samples of 0.56 h to 33 h parts (3 each) from lps4012 and lps4018. kit c402 contains samples of 220 h to 3300 h parts (3 each) from all five series. for details of kit contents and to order, contact coilcraft or visit http://order.coilcraft.com .
? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded smt power inductors C lps3008 series document 438-2 document 438-2 revised 08/25/10 typical l vs current 0.1 1 10 100 1000 0.01 0.1 10 1 current (a) inductance (h) 330 h 33 h 10 h 100 h 1.0 h 3.3 h typical l vs frequency 0.1 1 10 100 1000 0.01 0.1 10 1 frequency (mhz) inductance (h) 330 h 33 h 10 h 100 h 1.0 h 3.3 h -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 25c percent of rated current i sat i rms current derating dimensions are in inches mm 0.116 0.003 2,95 0,076 0.116 0.003 2,95 0,076 0.130 3,30 0.040 1,02 0.025 0,64 0.045 1,14 0.020 0,51 0.130 3,30 recommended land pattern 0.035 0,89 winding direction dash number internal code 0.0315 0,8 max xxx x * * dimensions are of the case not including the termination. for maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. * parts manufactured prior to september 2010 may be marked with only the dash number.
|
